This tutorial will show you how to add Clover Bootloader to Grub2 and Grub4dos, simply add a menu to chainload Clover from Grub2 and Grub4dos.
Install
Previous story Install-Grub-Bootloader-Kalilinux; Leave a Reply Cancel reply. Your email address will not be published. When you've done this, you type the command /sbin/grub-install followed by the location in which you want to install the GRUB stage 1 boot loader. For example, to install GRUB in the MBR of the master IDE drive, you type this command. root@gurkulindia1 /# /sbin/grub-install/dev/hda. The next time you boot the system, the GRUB boot loader.
On this site, I showed you how to install Clover Bootloader as well as how to install Grub2. In UEFI mode, when you install both of these bootloaders, only one bootloader is booted as default. The /EFI/BOOT/BOOTX64.EFI file will determine that, just keep this file, or back up and copy it back to let the system boot into the bootloader you want. Clover Bootloader currently no longer supports UEFI 32-bit.
AIO Boot supports all of these bootloaders, including Enoch Chameleon, Syslinux and rEFInd. In Legacy mode, just run AIOCreator.exe, then click on Bootloaders to install them.
Grub Bootloader Uefi
Add Clover to Grub2
Open the Grub2 configuration file (grub.cfg) and add the following code:
The Grub2 configuration file on Ubuntu, Linux and other Linux distributions is /boot/grub/grub.cfg, see how to add Grub2 menu.
Add Clover to Grub4dos
Grub4dos only supports Legacy. Open the Grub4dos configuration file (menu.lst) and add the following code:
Syslinux:
In Legacy mode, Grub2 and Grub4dos will boot Clover using the boot0ss file, you can use boot0af or boot0md, see more about these files here.
You can also boot into Grub2 and rEFInd from Clover Bootloader using UEFI Shell or add an entry to config.plist, see how to add Grub2 and boot Ubuntu and Linux Mint from Clover. Good luck!
Some time ago, I wrote a tutorial on how to reinstall Grub on Arch Linux after installing Windows.
A few weeks ago, I had to reinstall Arch Linux from scratch on my laptop and I discovered installing Grub was not as straightforward as I remembered.
For this reason, I'm going to write this tutorial since installing Grub on a UEFI bios during a new Arch Linux installation it's not too easy.
Locating the EFI partition
Install
Previous story Install-Grub-Bootloader-Kalilinux; Leave a Reply Cancel reply. Your email address will not be published. When you've done this, you type the command /sbin/grub-install followed by the location in which you want to install the GRUB stage 1 boot loader. For example, to install GRUB in the MBR of the master IDE drive, you type this command. root@gurkulindia1 /# /sbin/grub-install/dev/hda. The next time you boot the system, the GRUB boot loader.
On this site, I showed you how to install Clover Bootloader as well as how to install Grub2. In UEFI mode, when you install both of these bootloaders, only one bootloader is booted as default. The /EFI/BOOT/BOOTX64.EFI file will determine that, just keep this file, or back up and copy it back to let the system boot into the bootloader you want. Clover Bootloader currently no longer supports UEFI 32-bit.
AIO Boot supports all of these bootloaders, including Enoch Chameleon, Syslinux and rEFInd. In Legacy mode, just run AIOCreator.exe, then click on Bootloaders to install them.
Grub Bootloader Uefi
Add Clover to Grub2
Open the Grub2 configuration file (grub.cfg) and add the following code:
The Grub2 configuration file on Ubuntu, Linux and other Linux distributions is /boot/grub/grub.cfg, see how to add Grub2 menu.
Add Clover to Grub4dos
Grub4dos only supports Legacy. Open the Grub4dos configuration file (menu.lst) and add the following code:
Syslinux:
In Legacy mode, Grub2 and Grub4dos will boot Clover using the boot0ss file, you can use boot0af or boot0md, see more about these files here.
You can also boot into Grub2 and rEFInd from Clover Bootloader using UEFI Shell or add an entry to config.plist, see how to add Grub2 and boot Ubuntu and Linux Mint from Clover. Good luck!
Some time ago, I wrote a tutorial on how to reinstall Grub on Arch Linux after installing Windows.
A few weeks ago, I had to reinstall Arch Linux from scratch on my laptop and I discovered installing Grub was not as straightforward as I remembered.
For this reason, I'm going to write this tutorial since installing Grub on a UEFI bios during a new Arch Linux installation it's not too easy.
Locating the EFI partition
The first important thing to do for installing Grub on Arch Linux is to locate the EFI partition.
Let's run the following command in order to locate this partition:
We need to check the partition marked as EFI System
In my case is /dev/sda2 Pc logo turtle free download for windows 7.
After that, we need to mount this partition, for example, on /boot/efi:
2 | # mount /dev/sdb2 /boot/efi |
Grub Bootloader Usb
Another important thing to do is adding this partition into the /etc/fstab file.
Installing Grub
Now we can install Grub in our system:
Install Grub Bootloader On Windows
2 | # grub-mkconfig -o /boot/grub/grub.cfg # grub-install --target=x86_64-efi --efi-directory=/boot/efi --bootloader-id=GRUB |
You can find more about Grub on Arch Linux here. Kentucky mandolin serial numbers.
